The SB-1 500 Shuttle Buggy® material transfer vehicle features a low
transport height and weight and a narrow transport width. It can store up to 15 tons of
hot mix, allowing haul vehicles to unload as soon as they arrive. A triple-pitch Ni-Hard
segmented anti-segregation auger remixes the asphalt, eliminating segregation and cold
truck ends. It then transfers the mix without interfering with the paver's continuous
speed, creating pavement smoothness levels previously unattainable.
Click here for dimensions
ENGINE
Cummins 6 CTA8.3 diesel, 505 cu In (8.281), 6-cylinder engine, 276 HP (206 kw) 0 1,900
rpm. Engine instrumentation includes tach/hour meter, oil pressure, voltage and emergency
shutdown system.
OPERATOR'S STATION
Operator positions on both sides. Control panel swivels for use from either station
allowing for same-lane or adjacent-lane operation from either side. Inside turning radius
26'6' (8.1 m).
GROUND DRIVE
All hydrostatic for continuously variable speed control with four speed ranges. Hydraulic
shift between working and transport ranges. Maximum speed: (working range) 250ft1min
(76m/min), 2.8 mph (4.5 kph): (travel range) 11.6mph (18.7 kph).
TIRES
Large, high-flotation - 18:00 x 26' (45.7 m x 635 mm).
ELECTRICAL SYSTEM
Standard system includes heavy-duty alternator, battery, and circuit breaker protection of
all systems.
FUME EXTRACTION SYSTEM
Two blowers -total air flow 4,200 cu f/min. (118.9 cu m/min.). Fold-down10'(254 mm)
exhaust pipes. SLAT CONVEYORS TRUCK UNLOADING (C-1): High-capacity truck unloading system
with low deck height, 9'2'(2.8 m) side truck opening and 22"(559 mm) o.d. x 8.5* (216
mm) deep segmented converging auger for quick material flow. Conveyor has weld-on I lights
5/8' (16 mm) thick, 5.5' (140 mm) deep x 33 3/4'(857 mm) long. NI-Hard liner plates are
removable. Power dump front hopper has a vibrator on the bottom that helps keep material
moving. Fixed push roller is standard. Conveyor capacity is rated at 600 TPH (544 MTPH).
SURGE BIN (C-2)
Unloadsthe surge bin with a multi-pitch 22"(559 mm) o.d. x8.5"(216 mm) deep
antisegregation auger in the hopper. Conveyor system has weld-on flights 5/8' (16 mm)
thick, 7' (178 mm) deep x dual 16" (406 mm) long. Liner plates are Ni-Hard and
removable. Conveyor capacity is 600 TPH (544 MTPH).
PAVER LOADING (C-3)
Conveyor swings 48 degrees to either side of center. Maximum conveyor
discharge height Is 11'6' (3.5 m) from ground level.
Conveyor flights welded to the chain are 5/fr (16 mm) thick, 4
3/4'(121 mm) deep and 3(r (762 mm) long. Conveyor has bolted
1/2"(12.7mm)T-1 replaceable floor plates and doors. C-2 and C-3 conveyors
have on/off controls that are interlocked. Conveyor capacity is
600 TPH (544 MTPH).
HOPPER INSERT
A mass-flow paver hopper insert is used to increase the hopper capacity of a
conventional paver when used with the S13-1 500.
CAPACITIES
Fuel tank 120 gal (454 1)
Hopper 15 tons (13.6 MT)
material 110 lbs/cu ft (1,762 kg/cu m)
WEIGHTS
Shipping weight 60,000 lbs (27,216 kg)
SRAY DOWN SYSTEM OPTIONS
Hydraulic generator set
Windrow attachment
